These work only while the printer's own prompt is still on its screen - any button
press at the printer takes over.
The motions run but the UV LEDs stay off, so nothing cures.
Press here to jump to the Dry run switch.
All actions are disabled: print controls, SD changes, uploads, settings and firmware updates. Monitoring and "Send to printer" from the slicer keep working. Enable: printer → System → Advanced → Network.
Updating firmware
Do not power off the printer.
This page reloads automatically when it is back.
This page reloads automatically when it is back.
Getting started
Circles are steps to do - the printer ticks some off by itself, click the rest when done. Reopen this guide any time with the ? next to Manual.
State syncing…
Loading
SD card
-
Resin left (est.)
-
Est. resin
-
Layers
-
Est. time
-
Resin
-
Running time
-
Remaining time
-
Layer
-
Print controls
Model preview
Drag – rotate
Right-drag or Shift-drag – move
Wheel – zoom
Buttons – turn (bottom left) · move (top right) · zoom (bottom right)
◎ – back to the default view · cube – detailed view
Phone: one finger rotates, two move and pinch
Right-drag or Shift-drag – move
Wheel – zoom
Buttons – turn (bottom left) · move (top right) · zoom (bottom right)
◎ – back to the default view · cube – detailed view
Phone: one finger rotates, two move and pinch
3D
%
mm
STL slicer
No file loaded yet.
Layers are 0.05 mm, as for every model.
Supports and a raft are added where the part hangs.
SD manager
Uploaded SL1/ZIP files are unpacked into printable model folders on the SD card.
SD card-
Model list hidden while the slicer is open.
Model
Layers
-
Print layers
-
Height
-
Estimated time
-
Resin needed
-
⚠ Sliced at ? mm, not 0.05 mm - the printer assumes 0.05 mm, so this may print flat. Re-slice with a 0.05 mm layer height.
⚠ Layers are ?, not 320×240 - this file was sliced with the display set to portrait. It will print rotated. In PrusaSlicer: Printer Settings → Display → Orientation = landscape, then slice again.
Preview is built in the browser from every Nth sliced layer; the box is the printer's build volume (40.8 × 30.6 × 68 mm).
TinyMaker Connect
Loading Connect from the configured server...
Resin
Boot animation
Pick which animation plays at power-on and press Save config. Show plays it on the printer's screen (idle only) - check the printer. Delete removes the file from the SD card.
3D previews
Models show a real, turnable 3D view once their slice data is prepared. A model prepares itself the first time you open it - this does the whole card in one go.
All models
About half a minute per model, and only while the printer is idle. Old flat thumbnails are removed as each model is prepared.
Backup & restore?
Requires TinyMaker Connect registration.
The backup holds every setting and the lifetime counters. With a backup on the SD card, the printer offers to restore it on the first boot after a full USB reflash.
Firmware update
Checking...
Running a beta? Walk the test checklist - the report goes straight into the feedback form.
Flash a firmware.bin from GitHub Releases
Do not power off during an update - the printer reboots by itself when done.
Need a full USB reflash or recovery? Use the browser flasher (Chrome/Edge + USB cable).
Slicer module
On the printer
-
Latest
-
Checking...
Slicing engine: PrusaSlicer libslic3r 2.9.6 (© Prusa Research),
unmodified, under
AGPL-3.0.
Sources: prusa3d/PrusaSlicer.
3.6 MB is copied to the SD card, so the slicer works without internet. Nothing reboots; copying is refused while printing.
About
Firmware
-
Based on
TinyMaker3D 1.0.2
Build date
-
Open-source WiFi firmware for the TinyMaker MSLA printer by Viktoras Sidlauskas,
on top of the original TinyMaker3D firmware. Contributors: Brian Karmelk (Connect, web flasher),
Tanner Steorts (boot animations).
Config locks automatically while printing.
Statistics
Printed total
-
UV LED on-time
-
Last boot
-
Last interrupted print
-
Community printers
-
Most on
-
Network
WiFi
-
IP
-
System
Uptime
-
Free memory
-
Lowest ever
-
Largest free block
-
Plate height
-